The Mopeka® LCD Display is the first and only remote LCD display designed to pair seamlessly with up to two Bluetooth-enabled Mopeka sensors, including the Pro Check, Universal, Pro200 and Pro Plus models. Both user-friendly and highly portable, this compact display features a mounting bracket and built-in magnets so your sensors are always available when and where you need them. With its simple, robust design, the Mopeka LCD display delivers the precision and accuracy our customers expect.
With a battery life of up to 5 years and easily replaceable batteries, the Mopeka LCD Display allows you to control and configure your connected Mopeka Bluetooth sensors. You can switch between different media such as water, oil, propane and diesel and customise the screen time and brightness to suit your needs. The system also supports sensor configurations for vertical and horizontal tanks with preset options for tanks up to 1,000 gallons/ 3,785 litres or an "arbitrary" mode where you can enter custom tank dimensions, orientation and volume.
The Mopeka LCD display keeps you informed and in control.
- The display comes with 4 x CR2032 batteries pre-installed. To replace the batteries, remove the screws on the back of the display and remove the back cover. Place the batteries on one of the sides of the display with the negative side facing down in a double stack. Make sure that the batteries are firmly seated. Replace the rear cover and tighten the screws.
NOTE - The tank settings are set to 20-pound propane vertical tanks by default at start-up. To change settings and preset commodities, view the comprehensive installation video from the QR code.
Safety and warning instructions
Safety and warning instructions for Mopeka ultrasonic sensors with CR2032 battery
Introduction: Please read these safety instructions and warnings carefully before installing or using the Mopeka ultrasonic sensor. Follow the instructions to ensure safe use and avoid potential hazards.
1. general safety instructions
- Read the instructions: Keep these instructions for future reference and read them completely before using the device.
- Children: Keep the device and the CR2032 battery out of the reach of children as the battery can be swallowed and could cause serious injury.
2. warnings about the battery
- Ingestion hazard: CR2032 batteries can cause serious internal injury if swallowed. Seek medical attention immediately if the battery is swallowed.
- Explosion and fire hazard: Do not charge, disassemble or dispose of the battery in a fire. There is a risk of explosion and fire.
- Avoid short circuits: Ensure that the battery does not come into contact with metallic objects to avoid short circuits and overheating.
3. environmental and operating conditions
- Recommended environment: Only operate the sensor within the specified operating conditions (temperature range and humidity limit). Extreme environmental conditions such as high humidity or temperatures can impair sensor performance.
- Protection against chemicals: Do not expose the sensor to aggressive chemicals or corrosive substances, as these can damage the electronics.
4 Mounting and mechanical stability
- Mounting instructions: Ensure that the sensor is stable and correctly mounted to avoid mechanical damage. Incorrect installation can lead to measurement errors or failure of the sensor.
- Stable mounting surface: The sensor should not be installed on unstable or highly vibrating surfaces to ensure measurement accuracy.
- Flow direction: Ensure that the flow direction of the sensor is installed correctly according to the instructions on the device.
5 Electrical safety during installation and maintenance
- Safety measures during installation: Only install the sensor with clean and dry contacts to prevent short circuits. Electrical safety precautions must be observed during all installation and maintenance work.
- Proper installation: Installation and maintenance of the sensor should only be carried out by qualified personnel to ensure safe operation of the sensor.
6 Battery safety and correct handling
- Correct polarity: Ensure the correct polarity (+/-) when inserting the battery to prevent damage to the device.
- Replacement by qualified personnel: If the battery needs to be replaced, it is recommended that the replacement is carried out by qualified personnel to avoid damage.
- Temperature and sunlight: Avoid exposing the sensor and battery to direct sunlight or high temperatures to reduce the risk of overheating.
7 Storage and disposal
- Safe storage: Keep the sensor and spare batteries out of the reach of children and in a dry, cool place to prevent corrosion or battery leakage.
- Disposal of batteries: Never dispose of empty or damaged batteries in household waste. Instead, take them to an authorised collection point for batteries or a collection point to avoid environmental and health risks.
- Environmentally friendly disposal of the sensor: Dispose of the device in accordance with the applicable guidelines for waste electrical and electronic equipment (WEEE). Remove the battery before disposal and dispose of it separately.
8. maintenance and inspection of the sensor
- Regular inspection: Check the sensor every six months for visible damage, soiling or signs of wear.
- Cleaning: Use a soft cloth and mild detergent to clean the sensor. Do not use harsh chemicals or abrasive cleaners as this may damage the sensor.
- Replacement in case of damage: Replace the sensor immediately if visible damage or signs of wear are detected.
Manufacturer contact information
Manufacturer Contact
Mopeka Products, LLC
1223 Industrial Drive, Suite A
New Braunfels, TX 78130
USA
EU Contact
HybridSupply GmbH
Roggenhorsterstr. 9b
23556 Lübeck
Germany
https://hybrid.supply/contact
